Generates PCM 16 bit streams at From FW V3. The Inputs are used either to trigger streaming or to send contact closures to a partner device with SW loaded capable of decoding the information. Streaming Client V2. From FW V4. A printed version is included in the box and can also be downloaded from our site www. Technical specifications can be found in the corresponding product sheet which can be downloaded from our site www. If other HW is being used then the factory firmware will have to be replaced.
Before continuing with this manual make sure that the firmware version is up to date and corresponds with this manual. Please proceed to chapter 6 Updating the device in order to do so.
References to chapters e. X Chapter name are red and underlined and serve as direct links when viewed in Adobe Acrobat Viewer. Click on the link to jump to the referenced chapter, click on the left arrow icon to jump back to where you came from.
Some technical terms e. DHCP are underlined and red. Click on them to jump to the dictionary at the end of this manual, click on the left arrow icon to jump back. Click on any bookmark to directly jump to the corresponding part of the manual.
The middle frame shows current status information and permits the control of the streaming status, the simulation of the CTS input signal and the control of the RTS output. For details see the section below. For proper operation make sure you configure MP3 encoding and send always. All TCP connections are listed. A TCP connection is listed if and only if it's in the "established" state. The page is refreshed automatically.
The numbers [in dB full-scale] and the graphical VU meters show the peak values of the analog audio inputs line or microphone. Displays the audio input selected as source for encoding. In "send on Status of the hardware flow control signals of the device's RS interface. The signals can be used as a control input or output to control the device or an attached equipment. You can adjust network settings, streaming destinations, monitoring settings and more with the Web interface.
To enter the configuration mode you will need:. Help information will show up in the right, grey frame of the browser window. Other HW, for example, the Exstreamer series, may have additional options to support the enhanced features. The page allows the easy configuration of the most common use case of a single stream entry.
The same configuration parameters also appear under the Advanced Settings. Refer to these for more detailed information. Choose the desired Audio input source. Line mono and MIC inputs are mono, the other settings are stereo. Default setting is "Line stereo". Select encoding data format and sampling frequency. The default level is dB. Default setting is "send always". Choose the type of connection.
Note: only selected types are listed. Please see advanced settings for a complete list of options. Use an IP address 0. The IP address is ignored. An external device contacts this Instreamer on the given port and statelessly registers to receive the RTP stream.
If an active connection is required a Domain Name or an IP address can be provided. An example of a Domain Name is www. If an IP address is provided, e. Enter the port number for each destination between "0" and "". For Shoutcast, enter the base port the lower one, the same as clients put into their radio players. Default settings "0". A list of options is shown on the left together with the Network settings. The required page can be opened by selecting an option. Parameters can be changed at will on any of the pages.
It is only necessary to press the Apply button once after all changes have been made. This chapter explains how to adjust the network settings of the Barix device. The following diagram shows the network settings for automatic discovery See IP address below. However, we recommend that you set a Static IP address so that the device does not have to get a new IP address at power on or reboot..
Attention: Make sure that you enter a free IP address. The device will check this and will not be available until the device using the same IP is disconnected or switched off.
The command Ping can be used to ensure that a specific IP address is unused i. No reply. The automatic discovery functions are not executed if a Static IP address is set. If you have set a Static IP address then you will need to configure a valid Gateway address manually. From version VB3. Defines the port where the webserver of the Barix Exstreamer can be reached.
If set to "0" the default HTTP port 80 is used. Default: "0". The following table illustrates the DSCP values:. Check for DSCP services available in your network to set this value. Valid values are Default value is 0. Choose the desired input source. Line mono and MIC input are mono, the other settings are stereo. The options available depend on the HW according to the table below. The Exstreamer and Exstreamer have external Analogue to Digital circuitry which support input speeds of 32 and 48kHz.
The bit rate used for 8 and 24kHz G. Select the audio bit rate in kilobits per second. Please note that depending on the sampling rate not all bitrates are available.
New at Barix. November 03, News. Read more. October 06, News. June 14, Lab. May 11, News. April 28, Story. Reliable and Solid We create products that last. Up to Date Check the downloads for the latest firmware updates. Specialized Support The Barix support team contains of audio experts. Customizable Barix Products can be customized to special requirements. Next Page. Network audio encoder for commercial, industrial and security applications 55 pages.
Universal, multiformat ip audio decoder with amplifier, poe powered 26 pages. What exactly is the Barix Exstreamer? It is an audio network interface for your home stereo system that streams MP3s from your PC and radio stations from the internet. If you reboot your PC you will not zServer from www. It automatically will To stop the zServer simply close its window.
PLAY This action plays the media file. Page Playlists This action increases the volume by increment. Click it to go back or the folder above Click it to refresh the current list 5. See the section Receiver settings in seconds since the streaming buffer is empty until the Buffer Underrun Mode action will be executed. Barix Exstreamer to start up with custom sound adjustments. This This is to encrypt the data that is being wirelessly trans- name is displayed in the file info frame on the device status mitted to the wireless access point.
Set WEP mode to On page. Page Control Settings Defines the port for the active serial gateway function see When activated all received IR remote control commands destination IP.
0コメント