Enter a descriptive name in the Computer name field for this computer. This is how it will be listed on your network. Enter the workgroup name for this computer. All the computers connected to this network must be assigned to the same workgroup. Your computer will automatically be configured for your home network.
Select Just finish the wizard; I don't need to run the wizard on other computers and click Next. You will use the same flash drive or removable media that you used on this computer to configure the remaining network computers. You don't need to create another setup disk. Because Microsoft will not provide security updates for these operating systems, we recommend that you upgrade to a supported version immediately to ensure the best possible performance.
Request Quote Order Now. Installing and configuring a wireless home network using a D-Link router Steps to create a D-Link wireless home network Creating a D-Link DI wireless home network requires six steps:. Open Internet Explorer or any other browser on your computer. The Verizon home page should display. If the Verizon home page does not display, refer to the D-Link router troubleshooting tips. After you have solved the problem, repeat this test.
Steps to create a D-Link Di wireless home network Before you begin setting up your wireless network be sure that you have completed each item on the checklist below. Review the wireless networking system requirements Review the factors to consider before installing your wireless network.
Verify you have the required network adapters and accessories: D-Link Wireless USB adapterfor each desktop computer you are connecting to your network. Many newer computers are sold with wireless network adapters installed. Steps to create a D-Link DI wireless home network Although you can set up a home network in earlier versions of Windows, you will find it significantly easier if the computer connected to the router is running Windows XP.
Click All Programs 3. Click Accessories Note : The name cannot contain spaces or special characters. Click Communications 5. Select Network Setup Wizard 6. Note : The name cannot contain spaces or special characters. Review the instructions for using the setup disk. Steps to create a D-Link DI wireless home network Security is an important issue when using a wireless home network. Download the complete instructions for printing 2.
Change your default router password Your D-Link router's default values of "admin" as the user name and no entry in the Password field are well-known to hackers. Select the Tools tab and click Admin. Enter a new Administrator user name in the Login Name field.
Enter a new password in the New Password field. Enter the password again in the Confirm Password field. Enable MAC Address filtering You can limit access to your home network to increase the security of the information stored on it. Select MAC Filters. Repeat Steps 5 - 7 for each computer you are allowing to access your home network. Select the Tools tab and click Misc. Steps to create a D-Link DI wireless home network If you have additional computers you want to connect to your wireless network, please follow the directions below.
If you don't have a wireless network adapter installed , connecting an additional computer will require two major steps: Configure Windows on the computers you are adding to the network so they have the correct components for home networking installed.
Connect the other computers to your home network using Ethernet cable or wireless network adapters. Create a completely wireless network by installing and configuring wireless network adapters for each computer. Create a combination network by connecting any computers that are close to your router with Ethernet cable.
Then install wireless network adapters to connect notebook computers or computers that are farther away from the router. Completely Wireless Home Network No wires to clutter your work space Provides the most flexibility, especially for notebook computers Requires purchasing a wireless network adapter for each additional computer Combination Home Network Faster data flow and more security from hackers for the computers connected by Ethernet cable Less expensive. Computers close to the router and connected by Ethernet cable use a network interface card that is much less expensive than a wireless network adapter Easier installation for computers connected by Ethernet cable Connect additional computers by selecting either a completely wireless or a combination network.
Steps to create a D-Link DI wireless home network The final step is to test your Internet connection on each computer on your home network.
Open your Internet browser on the computer connected to your gateway. Note : If you cannot connect to the Internet, refer to the D-Link troubleshooting tips. If you want a completely wireless network, remove the Ethernet cable yellow in the illustration below that connects your computer to the D-Link router. DI Router. Before installing your wireless network, you should consider: Using the same operating system on all the computers connected to your network.
Placing your wireless router or gateway at least 10 feet from cordless phones or microwaves to avoid potential interference. Positioning your wireless router or gateway away from heat sources, moisture, excessive dust, or extreme cold. The wireless router is generally able to go through two or three walls before it loses connectivity. Positioning the devices connected to your network so the signals will go straight through a wall rather than at an angle.
If the signal hits a wall at an angle, the signal appears much larger and decreases its strength. Keeping the number of walls and ceilings between your router and the other devices on your network to a minimum.
Placing the wireless router or gateway near a window if you want to access the network outside. Keeping the wireless router or gateway away from any large metal objects, because they may adversely impact signal quality and speed.
Note : Resetting your D-Link router clears all of your home networking settings. To reset your D-Link router: With the power on Power LED on front panel should be lit green , use the pointed end of a paper clip to press and hold the Reset button for 10 seconds. Release the Reset button. The D-Link router will automatically reboot itself.
Wait 15 seconds before resuming setup. When time select to auto NTP, then apply will update the system time immediately. Enhancements: 1. The web page is Germany version. Fix WPA2 can't get ip issue. Fix wpa2 can't get ip issue. This version has JumpStart function. Fix dynamic turbo reboot. Fixed when use super G with dynamic mode, Auto Select button can't selection. Fixed WPA mode , when sta connect to device , the device wiil reboot.
Fixed JumpStart should be able to be reset by pressing the reset button in the device. Fixed JumpStart settings should be able to be saved unless to press the reset button in the GUI or physical button in the device. Fixed Reset JumpStart Function 2. Fixed Router will keep rebooting when the Station connected with encryption.
Fixed Under Firewall page if we want to modify IP, System always show "xxx has been already existing ". We must modify name together. Add JumpStart Function 2. Version V2. Change default wireless channel from "1" to "6". Fixed rules name of URL Filter can key-in the same key word 4.
Fixed rules name of Firewall can key-in the same name. Fixed bug no. Fixed under wizard page set password function can't be set empty.
Fixed Max characters in Server IP field is limit again to 16 characters instead of 32 characters as should be. Checksum error while trying to upload setting after firmware update 3.
UPnP issue Version V2. Enable AR mode in default setting. Change Atheros driver to V3. Improve throughput in dynamic turbo mode Version V2. Change GUI. Change virtual server entry port from Virtual Server to Firewall page. Update Atheros code v3. Update Atheros newest driver v3. Update Atheros patch code, station switch base and xr mode in some distance. Update Atheros patch, Dynamic turbo to base mode, beacon stop sending. Fixed shared key unstable with TI Client.
Fixed shared key unstable with non-atheros client. Support XR function 2. This build has backup mode re-built. Version v2. Add 2 virtual server entries by Cephalus. This is Shimano's older E-Tube Project version. Also, Version 3. You can download E-Tube Project 3. Note: in order to connect to the bike using a mobile app you need a wireless module.
These do not come standard on Di2 road bikes. It helps you plan your route, record your ride and upload it to Strava. Also, it lets you pair sensors and displays your current speed, cadence, and even power if you have compatible sensors installed. Its main use is as a cycle computer on E-Bikes and Urban bikes, but it also connects to road bikes and mountain bikes.
It is the mobile equivalent of the desktop application and lets you:. About Contact. Di2 E-Tube Software and Tools. What Windows E-Tube Project version do you need?
0コメント